ROTTARY MILLING TABLE (Horizontal Plain)
Dia of Table (in mm) | 150 | 200 | 250 | 300 | 375 | 450 | 500 |
---|---|---|---|---|---|---|---|
Size in inches | 6 | 8 | 10 | 12 | 15 | 18 | 20 |
Table T-Slot Size | 10 | 13 | 13 | 16 | 16 | 20 | 20 |
Centre Bush Bore (morse taper) | 2 | 3 | 3 | 3 | 3 | 4 | 4 |
Worm & Gear Ratio | 1:72 | 1:72 | 1:72 | 1:120 | 1:120 | 1:120 | 1:120 |
Wheel Calibration (in minutes) | 2 | 2 | 2 | 1 | 1 | 1 | 1 |
Height Overall | 95 | 105 | 110 | 130 | 135 | 160 | 160 |
Weight in kgs | 14 | 23 | 36 | 55 | 95 | 162 | 177 |
Remarks |
* High accuracy, easy reading of all dias clear & functional of all operating elements, sturdy yet good looking practical design. These are widely used for circular cutting, angle cutting, boring and spot facing with a milling macine.
* Works as an index center in the vertical position, as well as conventional Rotary Table, graduated 360°
Provision for fine adjustments when setting work piece.
ROTTARY MILLING TABLE (Horizontal & Vertical)
Dia of Table (in mm) | 150 | 200 | 250 | 300 | 375 | 450 | 500 |
---|---|---|---|---|---|---|---|
Size in inches | 6 | 8 | 10 | 12 | 15 | 18 | 20 |
Table T-Slot Size | 10 | 13 | 13 | 16 | 16 | 20 | 20 |
Centre Bush Bore (morse taper) | 2 | 3 | 3 | 3 | 3 | 4 | 4 |
Worm & Gear Ratio | 1:72 | 1:72 | 1:72 | 1:120 | 1:120 | 1:120 | 1:120 |
Wheel Calibration (in minutes) | 2 | 2 | 2 | 1 | 1 | 1 | 1 |
Height Overall | 240 | 300 | 365 | 425 | 530 | 620 | 620 |
Weight in kgs | 16 | 27 | 42 | 65 | 100 | 175 | 187 |
Remarks |
* Direct reading to 2 minutes for size 6", 8" and 10" on hand wheel scale.
* Accuracy : Maximum error 4 minutes of circular division using hand wheels
* Working surface rotates in its own plan to within 0.03mm
* Horizontal and Vertical supporting surface square with 0.01mm/100mm
* Direct reading to 1 minute for size 12" on hand sheet scale & Table flatness within 0.01mm/100mm &
Center bush bore is true to table axis within 0.03mm
TILTING TABLE
Size of Table (in mm) | 125 x 175 | 175 x 150 | 250 x 375 |
---|---|---|---|
Size in inches | 5 x 7 | 7 x 10 | 10 x 15 |
Height Overall | 98 | 168 | 174 |
T-Slot Size | 13 | 16 | 16 |
Calibration code | 0 to 90° | 0 to 90° | 0 to 90° |
Weight in Kgs. | 9 | 22 | 45 |
Remarks |
* Special design for angle setting on various machine tools.
* Low profile for larger working space.
* The table is set manually to the required Tilt and is locked in the set position by means of two locking clamps held through
bolts.
* Can be adjusted by 45 degree on both right-hand and left-hand side.
* The angle marking are accurate and easy to read.